This essay has been submitted by a student. This is not an example of the work written by professional essay writers.
Hardware

DIY Folding Kayak – Step by Step Guide for making a Fabulous Folding Kayak

Pssst… we can write an original essay just for you.

Any subject. Any type of essay. We’ll even meet a 3-hour deadline.

GET YOUR PRICE

writers online

DIY Folding Kayak – Step by Step Guide for making a Fabulous Folding Kayak

Do you wish to go for expeditions on the water but cannot do it due to the high prices of kayaks? Or are you discouraged from kayaking since you don’t have enough space to transport and store your vessels? Worry not because, with proper guidance, you can create a folding kayak on your own and enjoy every aspect of water touring. Here is a step by step guide for creating your foldable kayaks.

Collection of the necessary materials

The following materials are vital when you want to make you’re a boat by yourself. They are available from your local hardware shop.

  • 200-inch untreated canvas
  • 2-1/4-inch 4-inch by 8-inch untreated plywood sheets with one smooth side
  • Heavy-duty Velcro
  • Waterproof wood glue
  • Exterior latex paint
  • 1-piece wood lath
  • 1-inch by 2-inch wood for seat support rails
  • Exterior latex primer
  • Six or more c-clamps
  • 2 – 2-inch screws and matching nuts

    Don't use plagiarised sources.Get your custom essay just from $11/page

Ensure that one of the plywood sheets is cut into four pieces that measure 1-inch by 8-inch. You can request the nearest home-improvement store to do it for you.

Cut the Cockpit and paint the interior interior

Clamp the two sides of the plywood sheets together (one must be cut into 4 – 1-inch by 8-inches). The two smooth hands should touch each other. It would help if you then cut the cockpit opening starting around 41-inches from the front of the kayak. The cut should be about 5-inches deep and 28-inches long.

After deciding the shape of your kayak, clamp together the four pieces of the wood to ensure the cuts match and that the kayak is symmetrical. Round the edges of the boat and create your desired shape, ensuring that the front and the rear are not too pointy. Tape the wood and install the strips to attach the unpainted pieces. You should then paint the interior of the vessel with two coats of flexible exterior latex paint.

Making Spreaders and Spacers

Spreaders

It would help if you made two spreaders, each consisting of two 1/4-inch pieces of plywood already joined together.  Cut four, 11-inch by 24-inch pieces of 1/4 –inch plywood. You should the bond then bond the wood using wood glue and C-clamps making two thick triangles of 1/2 –inch. The spreaders should then be cut to the desired dimensions. You can also cut the center of the spreader to reduce its weight.

Spacers

Spacers are useful in holding the kayak pieces together in the right configuration when applying the edge canvas. You can use scrap wood to make the spacers by following the steps below:

  • Cut two pieces of plywood each measuring 3-inch by 3-inch
  • Cut four pieces of plywood measuring 2-inch by 6-inch
  • You should bore a hole through the center of each piece of wood. Insert the 3-inch by 3-inch wood pieces of timber between two of the 2-inch by 6-inch. Join the pieces with a 2-inch screw and matching nuts.

Preparing the Canvas and Assembling the Kayak

It would be best if you assembled the kayak using 5-strips of canvas with the following dimensions

  • One 13-inch by 12-inch
  • Two 4.5-inch by 46-inch
  • Two 4.5-inch by 72-inch

You should draw the outlines of the strips on the art and paint it with 2-layers of contact cement. Allow the adhesive to dry as you apply before cutting to prevent the edges from fraying. It would help if you then assembled the kayak with the spacer blocks.

Draw a line that is 2-inches from the edge around the kayak and apply contact cement to it. Allow the adhesive to dry as you use and repeat it on the bottom of the vessel. You should then apply the canvas strips with the 2-inch marked line as a guide. Apply the shorter pieces to the front and rear of the boat and the longer ones to the sides.

Stretch the canvas and apply slowly while smoothing the wrinkles. After you are done utilizing on one side, slip over the kayak and use the remaining cloth to the bottom. Apply contact cement where the strips overlap to secure them. Leave to dry for a few hours, then install the spreaders.

Installing the Stop Blocks

Use eight stop blocks to hold each spreader board in position and allow them to pop into place between the stop block. You then need to cut sixteen stop blocks from the wood lath as per your desired dimensions.

Install the spreader boards at your desired position and get in your kayak. You should ensure that you have enough space where you can spread your legs. You should then install the stop blocks on the unpainted sections of the interior side of the kayak by use of waterproof wood glue.

Installing the Center Canvas

After measuring the widest gaps and the front and back of the Cockpit, install the spreader boards.  Add four inches to the most significant difference to allow two inches of the canvas glued to the wood on every side. Cut out a strip approximately 13-inches long, center and clamp it onto the kayak. Mark the painting at the front and back of the kayak and tamper it at both spots to match the width.

You should then install the canvas with clamps and outline it on the kayak: Joint the kayak and the tent with contact cement starting from either side.

Assembling the Seat and its Rails

Join two pieces of plywood with a canvas hinge and let it sit on two rails that are glued to the floor of the kayak. Attach the seat to the vessel with Velcro. Cut two tracks of the desired length from a piece of wood with a dimension of 1-inch by 2-inch and attach to the unpainted section of the kayak’s floor.

To make the seat, cut two plywood rectangles whose size depends on the spreaders installed in the kayak. The width will also depend on the distance between the seat rails. It would help if you then cut out a small piece of canvas to act as a hinge and attach the two parts. Finally fix the Velcro to the seat and rails

Painting the Kayak

The final step in making a folding kayak is to brush and prime it, the place and the spreader boards. Ensure that the items have at least three coats of paint to make them flawless and durable.

Final Verdict

If you are an enthusiast with kayaking, you need not break a bank to acquire a suitable vessel. Follow the simple step by step DIY guide and let nothing stop on your way. You can enjoy the adventures in water without having to stress yourself.

Let only your imagination on the waters be the only limit!

 

 

 

  Remember! This is just a sample.

Save time and get your custom paper from our expert writers

 Get started in just 3 minutes
 Sit back relax and leave the writing to us
 Sources and citations are provided
 100% Plagiarism free
error: Content is protected !!
×
Hi, my name is Jenn 👋

In case you can’t find a sample example, our professional writers are ready to help you with writing your own paper. All you need to do is fill out a short form and submit an order

Check Out the Form
Need Help?
Dont be shy to ask