This essay has been submitted by a student. This is not an example of the work written by professional essay writers.
Uncategorized

How to make a portable miter saw stand?

Pssst… we can write an original essay just for you.

Any subject. Any type of essay. We’ll even meet a 3-hour deadline.

GET YOUR PRICE

writers online

How to make a portable miter saw stand?

Miter saw is an essential tool when it comes to a workshop or even for any DIY projects. A miter saw stand is a mandate to work with ease with a portable miter saw. Typically aligned towards the left to the right of a miter saw, the level of this stand is absolutely in line with that of a miter saw.

A miter saw is a small tool which can be port from one place to another quickly, taking along the miter saw stand is not feasible. It leads to the requirement of a portable miter saw stand. Depending on the model of a compound miter saw, varied portable miter saw stands are available to choose from.

Being a DIY enthusiast, If you wish to make a portable miter saw stand, here we go.

Material required

2x6x12-foot treated wood: 1 piece

2x4x8-foot treated wood: 5 pieces

2x6x8-foot treated wood: 2 pieces

Melamine-covered particleboard: a 2×3-foot piece with a thickness of 3/4-inch

Don't use plagiarised sources.Get your custom essay just from $11/page

1-5/8-inch deck screws

2-1/2-inch deck screws

3-foot-long, 1/2-inch-diameter bolts with a nut, lock washer and two washers: 4 pieces

Hand Saw

Compass

Chisel

Pencil

Combination square

 

How to make a portable miter saw stand?

Start with making the support structure beneath the table.

Cut four pieces of wood with the dimension of 2×6 at 31 inches long, 0-1/4 inches for the ends along with two at 7-1/4 inches for centre supports.

Take 2-1/2-inch deck screws to attach the one piece of butt to another

Take the opposite side of the piece of one wood to connect with another side of the end piece

After connecting all the four parts to form the corners, place the fifth piece at the middle

Create another box structure with a similar way

Position both the box structure parallel to each other

Place a scrap piece acting a spacer of dimension 2X6

Take one wooden melamine coated piece of dimension 24×36-inch piece of 3/4-inch-thick

Attach the above over the box structures carefully using deck screw

Now remove the spacer carefully

As the saw table is complete, build leg assemblies for supporting the stand.

With a length of 40 inches 4 pieces care required with a dimension of 2X4

To set the cutting surface 34 inches above the ground, you need to cut the length of legs at 32 inches.

Align the top cuts of the two different sets of legs

Clamp the pieces together by positioning a scrap of stock in between

Take long deck screw to attach trapezoidal-shaped pieces of stock to the legs

Attach the cross braces to the top and the bottom of the leg assemblies

The stabilizing braces are attached at the distance of 10-12 inches from the bottom of the leg

To provide considerable lateral support, a beam is required after the leg assembly

Once the beam is ready, put up the stand together by sliding each leg to the assembly

Fit the cross-braces of each leg assembly within each pair of beam notches.

After connecting legs to the beam, flip it onto the legs.

Check the beam pushing it hard; it should not wobble

Position the saw table on to the beam and fit the box structures  under its tabletop

Place the miter saw in the position where the fence is parallel to the beam’s far side to mark the bolt hole location.

Drill the holes by removing the saw and align the mitre saw carefully after that

Your portable miter saw table is ready.

 

 

 

  Remember! This is just a sample.

Save time and get your custom paper from our expert writers

 Get started in just 3 minutes
 Sit back relax and leave the writing to us
 Sources and citations are provided
 100% Plagiarism free
error: Content is protected !!
×
Hi, my name is Jenn 👋

In case you can’t find a sample example, our professional writers are ready to help you with writing your own paper. All you need to do is fill out a short form and submit an order

Check Out the Form
Need Help?
Dont be shy to ask